Smartek-systems SVS-1 User Guide-Part B Instrukcja Użytkownika

The SmarTek Video Detection System (SVS-1)User Guide-Part BUsing SVS Setup and Monitor Version 331 May 2011

Setting Light Reference and Visibility Parameters1) Select the Light Reference by clicking the LZ = button below the camera image until L Ref appears.

Setting Output - Example Scenario SummaryFrom the Main Setup display, proceed to the Set Output display by clicking the Set Output button. This displa

Setting Output Example Scenario Summary (Continued)4) BIU #1 Card file Detector/Controller Interface with 4 Relays per SVS-1 card, Slot 4 used, and 3

Scenario 1 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 1 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 1 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 2 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 2 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 2 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 3 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

SVS-1 – Setup Process OverviewThe primary function of the SVS Monitor and Setup Program is to provide the SVS-1 installer the means to quickly and eas

Scenario 3 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 3 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 4 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 4 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 4 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 5 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 5 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 5 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 6 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Scenario 6 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

SVS-1 – Opening the SVS Set Line Zones Window After camera installation and connection to the SVS-1 Video Image Detection System, run SVS Monitor and

Scenario 6 Set Output RelaysSelect Detector Interface and Route Relays:1) Click the Detector Interface button to select the type of detector/control

Set Output Video Text DisplayThis display is used to enter descriptive text which may be set to show on the output video image. Enter descriptive tex

Next, click the OK button on the Detection Zone Setup window to capture the settings and close the window.Closing Setup Windows and Saving Setup Param

Assigning Line Zones to a Phase and Routing to the Output Detector ChannelsDetection Line Zone NumberThis display may also be used to combine Detectio

Combining Line Zones and Assigning Them to a PhaseCurrent Camera Channel IDPhase LabelCheck Boxes Specify Detection Line ZonesAssigned to PhaseDetecti

Routing/Mapping Each Phase to an On Board Connector Relay PositionThe three columns at the center of the window are used to set the Detection Extensio

Routing Each Phase to a BIU Detector Channel Using SVS Relay Interface Cards1) Click the Clear All Detector Routing Check Boxes button to clear all of

Routing Each Phase to SVS Relay Interface Card Edges for a Type 170 Card file1) Click the Clear All Detector Routing Check Boxes button to clear all o

Routing Each Phase to a BIU-SDLC Detector Channel1) Click the Clear All Detector Routing Check Boxes button to clear all of the right side routing che

Next, click the OK button on the Detection Zone Setup window to capture the settings and close the window.Closing Setup Windows and Saving Setup Param

SVS-1 – Opening the SVS Set Line Zones Window If a network connection is selected, set the SVS-1 IP address and Port number in the SVS Network Connect

SVS-1 – Sending Parameters to a Specific SVS-1 Camera Processing Channel (SVS ID) After setting up all Line Zones, Circle Zones, the Light Reference P

SVS-1 Banner DisplayFrom the SVS main display, click the Settings/Visible Message Window menu item to open the message window. Then click the SVS/Get

SVS-1 – Detection Zone Sensitivity Parameters Detection Threshold – Specifies Line Zone detection sensitivity and may be adjusted by changing the Dete

SVS-1 – Detection Zone Sensitivity Parameters (continued) No Motion Timeout – Specifies the amount of time in minutes that must pass in the absence of

SVS-1 – Setting Detection Zone Sensitivity Parameters (continued) Circle Zone Radius– Specifies the size of the Circle Detection Zone. The circle zon

SVS-1 – Setting Light Reference Parameters and Visibility ParametersLight Reference Detection Threshold– Specifies the threshold that the position of

Setting up the SVS-1 using SVS Setup and Monitor Version 3 (PC Required)After clicking the SVS/Get Image for Zone Setup menu item to open the Zone Set

Main Setup DisplayWhen setting up an SVS-1 camera channel for detection, the user should proceed by first Drawing Line Zones, then Setting LZ Paramet

Draw Line Zones Set Line Zone Position, Size and Phase Group:1) Click the LZ= button to select the line zone to draw. If the previous line zone has

Draw Line Zones Phase assignment Codes:Ph-1LPh-6TPh-6RPh-3LPh-8TPh-8RPh-5LPh-2TPh-2RPh-7LPh-4TPh-4RPh-9LPh-14TPh-14RPh-11LPh-16TPh-16RPh-13LPh-10TPh-1

Setting Detection Zone Parameters1) Click the Default Parameters-All LZs button below the Image display 2) Click Main Setup button to return to the Ma